Logic Pro for Mac 12.3
Logic Pro for Mac 12.2
Logic Pro for Mac 12.0
Logic Pro for Mac 11.2
Logic Pro for Mac 11.1
Logic Pro for Mac 11.0
Logic Pro for Mac 10.8
Logic Pro for Mac 10.7.8
Logic Pro 10.7.5
Logic Pro 10.7.3
Logic Pro 10.7
Logic Pro 10.6.2
Logic Pro 10.6
Logic Pro X 10.5
سيؤدي تعديل زر التحكم إلى إعادة تحميل هذه الصفحة تلقائيًا

Create fades in Logic Pro

You can fade in the beginning of audio regions, and fade out the end of audio regions (including audio Apple Loops).

Fades are only visible if you are zoomed in enough to see the waveform in the audio region. You can create a fade using either the Fade tool or the Fade In and Fade Out parameters in the Region inspector.

Create a fade-in or fade-out with the Fade tool

  1. In Logic Pro, select the Fade tool.

    Figure. Fade tool.

  2. Do one of the following:

    • Drag over the start or end point of an audio region.

      Figure. A pair of images showing fade in creation on a region using the Fade tool.

      A fade-in or fade-out is created. The length of the fade drag area determines the length of the fade, so a longer drag area results in a longer fade time, and a shorter drag area, a quick fade.

    • Drag over the end point of one audio region and the start point of the region that follows.

      Figure. A pair of images showing fade creation between regions using the Fade tool.

      This technique works even if the two sections don’t directly adjoin each other.

With the Fade tool selected, you can edit fades on regions after you make them.

Create a fade-in or fade-out using the Region inspector

  1. In Logic Pro, select one or more regions.

  2. Set the value for the Fade In or Fade Out setting in the Region inspector by dragging the pointer vertically, or double-clicking and entering a value.

    Figure. Fade In parameter in the Region inspector, also reflected in Arrange area.

Fades created using the Fade tool and the Region inspector are interactive. After you create a fade using the Fade tool, for example, you can adjust the fade using the Region inspector Fade In or Fade Out parameters.

Apply the last fade to selected regions

  1. In Logic Pro, select one or more regions.

  2. Use the “Apply Last Fade or Fade Marquee Selection” key command.

The Apply Last Fade or Fade Marquee Selection command applies the following region parameters to the selected regions:

  • Fade In/Speed up–Time

  • Fade In/Speed up–Curve

  • Fade Out/Slow Down–Type

  • Fade Out/Slow Down–Time

  • Fade Out/Slow Down–Curve

The Fade Out/Slow Down Type change from “Out” to “EqP Crossfade,” or from any of the “Crossfade” types to “Out” depending on whether an adjacent region following the selected region (requires EqP Crossfade) or a gap (requires Out) exists.

Apply the last fade to a marquee selection

  1. In Logic Pro, make a marquee selection to part of one or more regions.

  2. Use the “Apply Last Fade or Fade Marquee Selection” key command.

In case there is a marquee selection, the following are applied for every affected track:

  • When the marquee selection encloses one region end which is followed by a gap, or the marquee selection starts later than the region start and ends exactly on the region end (within the same pixel, or so): apply a Fade Out from the marquee selection start to the region end.

  • When the marquee selection encloses exactly one junction between two adjacent regions (starts later than the first region start, ends earlier than the second region end): apply an Equal Power Crossfade from the marquee selection start to the marquee selection end, with the crossfade pivot on the region junction.

  • When the marquee selection encloses a region start, which follows a gap, or if the marquee selection starts on the region start and the marquee selection ends before the region end: apply a Fade In from the region start to the marquee selection end.

Morty Proxy This is a proxified and sanitized view of the page, visit original site.
هل كان هذا مفيدًا؟
الحد الأقصى للأحرف: 250
الحد الأقصى للأحرف 250.
شكرًا على ملاحظاتك.
Morty Proxy This is a proxified and sanitized view of the page, visit original site.