Logic Pro for Mac 12.3
Logic Pro for Mac 12.2
Logic Pro for Mac 12.0
Logic Pro for Mac 11.2
Logic Pro for Mac 11.1
Logic Pro for Mac 11.0
Logic Pro for Mac 10.8
Logic Pro for Mac 10.7.8
Logic Pro 10.7.5
Logic Pro 10.7.3
Logic Pro 10.7
Logic Pro 10.6.2
Logic Pro 10.6
Logic Pro X 10.5
Hvis denne funktion ændres, opdateres denne side automatisk

Modulator envelope in Logic Pro for Mac

Figure. Modulator Envelope parameters.

Modulator Envelope parameters

  • Envelope on/off button: Turn the envelope on or off.

  • Envelope display: Shows the current envelope shape. Drag the handles in the display to set the following parameters:

    • Delay: Delay the onset of the envelope. Ranges from 0 to 10 seconds.

    • Attack: Set the time required to reach the sustain level. Ranges from 0 to 10 seconds.

    • Hold: Set the sustain level and duration. Ranges from 0 to 10 seconds.

    • Release: Set the time required for the envelope to fall to a value of zero after the sustain phase of the envelope has finished. Ranges from 0 to 10 seconds.

  • Trigger switch: Determine if the envelope is triggered by the LFO or by incoming MIDI note on messages.

    • LFO: The envelope is retriggered when the LFO reaches its (positive) peak value. See Modulator LFO.

      Note: The envelope ignores incoming LFO triggers if it is currently completing an envelope pass.

    • Single: After all notes have been released, the envelope is re-triggered by the first MIDI note on message it receives.

      Note: This means that legato playing does not reset the envelope, so keep this in mind during performances.

    • Multi: The envelope is re-triggered by each received MIDI note on message.

  • Steps per Env(elope) Pass slider and field: Determine the number of steps per envelope pass. By default, the envelope produces a smoothed continuous stream of controller events, but you can use this parameter to create a stepped controller signal that is similar to the output of a Sample and Hold circuit. When you set a manual step rate, the envelope time can be changed without altering the number of steps.

  • Env to LFO Rate knob: Set the maximum amount of LFO modulation (LFO depth). The LFO rate can be modulated by the Attack, Hold, and Release parameters (see above).

  • Env to LFO Amp knob: Set the maximum amount of LFO output modulation. You can then fade the LFO in or out with the envelope.

  • To pop-up menu: Choose a continuous controller number, aftertouch, or pitch bend as the envelope output target. You can also learn a plug-in parameter.

  • Output Level slider: Scale the envelope output level.

  • Offset slider: Set a positive or negative offset in order to tailor the output for the intended target.

  • Oscilloscope: Displays the shape of the envelope control signal before it is scaled.

  • MIDI Channel pop-up menu (extended parameter): Click the disclosure arrow at the lower left. Choose a MIDI output channel.

Assign a MIDI event to a plug-in parameter

You can assign and send MIDI events to plug-ins in the same channel strip, allowing you to control parameters without using MIDI CC messages.

  1. In Logic Pro, choose Learn Plug-in Parameter from the To pop-up menu.

  2. Click the parameter in the target plug-in.

    The name of the plug-in and parameter are shown in the To field.

Download the guides:

Logic Pro User Guide: PDF

Logic Pro Instruments: PDF

Logic Pro Effects: PDF

Control Surfaces Support Guide: PDF

Morty Proxy This is a proxified and sanitized view of the page, visit original site.
Nyttig?
Maks. antal tegn: 250
Maks. antal tegn er 250.
Tak for din feedback.
Morty Proxy This is a proxified and sanitized view of the page, visit original site.