Logic Pro for Mac 12.3
Logic Pro for Mac 12.2
Logic Pro for Mac 12.0
Logic Pro for Mac 11.2
Logic Pro for Mac 11.1
Logic Pro for Mac 11.0
Logic Pro for Mac 10.8
Logic Pro for Mac 10.7.8
Logic Pro 10.7.5
Logic Pro 10.7.3
Logic Pro 10.7
Logic Pro 10.6.2
Logic Pro 10.6
Logic Pro X 10.5
سيؤدي تعديل زر التحكم إلى إعادة تحميل هذه الصفحة تلقائيًا

Edit comps in Logic Pro for Mac

You can edit comps by changing the start or end point of take sections, by moving a selected comp area to the left or right, or by alternating selected comp areas between takes. You should save a comp before editing it. Any subsequent changes automatically create a new comp.

Edit sections of different take regions

In the Logic Pro Tracks area, do one of the following:

  • To extend a take section: Place the pointer over the start or end point of a take selection, then drag.

    Figure. Dragging the end point of a take selection.

    Extending a take selection (dragging the start point to the left or the end point to the right) shortens adjacent selections on other takes. Shortening a take selection (dragging the start point to the right or the end point to the left) extends adjacent selections on other takes. This ensures that you don’t create silence between take selections.

  • To shorten a take section: Place the pointer over the start or end point of a take selection, then Shift-drag.

    Figure. Shift-dragging the end point of a take selection.

    Shortening a take selection (dragging the start point to the right or the end point to the left) does not extend adjacent selections on other takes. This allows you to create silence between take selections.

Note: If you’ve enabled Quick Swipe and Take Editing click zones in Logic Pro > Settings > General > Editing, make sure you place the pointer over the bottom half of the take region.

Move a selected area to the left or right

  • In the Logic Pro Tracks area, place the pointer over the center area of a take selection, then drag when the pointer changes to a two-headed arrow.

    Figure. Dragging the center area of a take selection.

This action moves the selection, while at the same time extending or shortening any adjacent take selections.

Note: If you have enabled Quick Swipe and Take Editing click zones in Logic Pro > Settings > General > Editing, make sure you place the pointer over the bottom half of the take region.

Alternate selected areas between take lanes

  • In the Logic Pro Tracks area, click an unselected area of a take to make that particular area active and part of the comp.

    Figure. Clicking an unselected area of a take.

The same area is automatically deselected in another take. This is a quick way to compare a section of two different takes.

Note: If you have enabled Quick Swipe and Take Editing click zones in Logic Pro > Settings > General > Editing, make sure you place the pointer over the bottom half of the take region.

Remove a take selection from the comp

  • In the Logic Pro Tracks area, Shift-click the take selection.

    Figure. Shift-clicking a selected area of a take.

Remove an entire take from the comp

  • In the Logic Pro Tracks area, Shift-click the header area of the take.

    Figure. Shift-clicking a take’s header area.

If the take doesn’t contain any selections, all unselected areas in other takes are selected in the take you click.

Download the guides:

Logic Pro User Guide: PDF

Logic Pro Instruments: PDF

Logic Pro Effects: PDF

Control Surfaces Support Guide: PDF

Morty Proxy This is a proxified and sanitized view of the page, visit original site.
هل كان هذا مفيدًا؟
الحد الأقصى للأحرف: 250
الحد الأقصى للأحرف 250.
شكرًا على ملاحظاتك.
Morty Proxy This is a proxified and sanitized view of the page, visit original site.