forked from Arduino-IRremote/Arduino-IRremote
-
Notifications
You must be signed in to change notification settings - Fork 0
Expand file tree
/
Copy pathirSend.cpp
More file actions
90 lines (75 loc) · 3.19 KB
/
Copy pathirSend.cpp
File metadata and controls
90 lines (75 loc) · 3.19 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
#include "IRremote.h"
#include "IRremoteInt.h"
//+=============================================================================
void IRsend::sendRaw (const unsigned int buf[], unsigned int len, unsigned int hz)
{
// Set IR carrier frequency
enableIROut(hz);
for (unsigned int i = 0; i < len; i++) {
if (i & 1) space(buf[i]) ;
else mark (buf[i]) ;
}
space(0); // Always end with the LED off
}
//+=============================================================================
// Sends an IR mark for the specified number of microseconds.
// The mark output is modulated at the PWM frequency.
//
void IRsend::mark (unsigned int time)
{
TIMER_ENABLE_PWM; // Enable pin 3 PWM output
if (time > 0) custom_delay_usec(time);
}
//+=============================================================================
// Leave pin off for time (given in microseconds)
// Sends an IR space for the specified number of microseconds.
// A space is no output, so the PWM output is disabled.
//
void IRsend::space (unsigned int time)
{
TIMER_DISABLE_PWM; // Disable pin 3 PWM output
if (time > 0) IRsend::custom_delay_usec(time);
}
//+=============================================================================
// Enables IR output. The khz value controls the modulation frequency in kilohertz.
// The IR output will be on pin 3 (OC2B).
// This routine is designed for 36-40KHz; if you use it for other values, it's up to you
// to make sure it gives reasonable results. (Watch out for overflow / underflow / rounding.)
// TIMER2 is used in phase-correct PWM mode, with OCR2A controlling the frequency and OCR2B
// controlling the duty cycle.
// There is no prescaling, so the output frequency is 16MHz / (2 * OCR2A)
// To turn the output on and off, we leave the PWM running, but connect and disconnect the output pin.
// A few hours staring at the ATmega documentation and this will all make sense.
// See my Secrets of Arduino PWM at http://arcfn.com/2009/07/secrets-of-arduino-pwm.html for details.
//
void IRsend::enableIROut (int khz)
{
// FIXME: implement ESP32 support, see IR_TIMER_USE_ESP32 in boarddefs.h
#ifndef ESP32
// Disable the Timer2 Interrupt (which is used for receiving IR)
TIMER_DISABLE_INTR; //Timer2 Overflow Interrupt
pinMode(TIMER_PWM_PIN, OUTPUT);
digitalWrite(TIMER_PWM_PIN, LOW); // When not sending PWM, we want it low
// COM2A = 00: disconnect OC2A
// COM2B = 00: disconnect OC2B; to send signal set to 10: OC2B non-inverted
// WGM2 = 101: phase-correct PWM with OCRA as top
// CS2 = 000: no prescaling
// The top value for the timer. The modulation frequency will be SYSCLOCK / 2 / OCR2A.
TIMER_CONFIG_KHZ(khz);
#endif
}
//+=============================================================================
// Custom delay function that circumvents Arduino's delayMicroseconds limit
void IRsend::custom_delay_usec(unsigned long uSecs) {
if (uSecs > 4) {
unsigned long start = micros();
unsigned long endMicros = start + uSecs - 4;
if (endMicros < start) { // Check if overflow
while ( micros() > start ) {} // wait until overflow
}
while ( micros() < endMicros ) {} // normal wait
}
//else {
// __asm__("nop\n\t"); // must have or compiler optimizes out
//}
}