USB-IF eStore Details
Prior to purchasing products from the USB-IF, please review our return policy and legal disclaimer.
USB 2.0 Hi-Speed Signal Quality Test FixturesThe USB-IF test fixtures used for certifying signal quality of hi-speed hosts and peripherals. The fixtures eliminate the need for probes and require quality SMA cables for direct connection to the scope. The fixtures include USB cables but do not include SMA cables. The USB-IF does not sell or provide SMA cables and it is the vendor’s responsibility to obtain them. One recommendation for SMA cables includes the following: Agilent 15443A Matched Cable Pair (or equivalent).
Each test fixture set includes the following:
qty 1 - Device test Fixture
qty 1 - Host test fixture
qty 2 - Standard A to Standard B 1-meter cable
qty 1 - Standard A to Standard B short cable
qty 1 - Standard A to Micro B short cable
The USB 2.0 Hi-Speed Signal Quality Test Fixtures are available for US$650 (members) or US$900 (non-members). To purchase these fixtures, please fill out the USB Product Order Form and fax or mail it to the address provided on the form. For an introduction on how to use these fixtures, please refer to the Test Fixture Set-up Guide. For more information, please contact your test equipment vendor or see the Testing Requirements.
USB 2.0 Link Power Management (LPM) Peripheral Development Kit (PDK)The USB 2.0 Link Power Management (LPM) Peripheral Development Kit (PDK) provides a host-side solution. It is intended to assist companies who are developing USB peripherals with the LPM feature.
The PDK includes a PCIe add-in host controller card that supports LPM L1. The cost of the PDK is US$800 (members) and US$1000 (non-members). The software to use with the PDK is available for download on the USB Tools page. Please direct questions regarding the LPM PDK to ssusbcompliance@usb.org.
To purchase the USB 2.0 LPM PDK, please fill out the USB Product Order Form and fax or mail it to the address provided on the form.
The LPM PDK is the same product as the Fresco USB 3.0 xHCI-based PDK for SupersSpeed USB.
USB 3.0 Electrical Test Fixture Kit
The USB 3.0 Electrical Test Fixture Kit provides a worst case, ISI hardware channel for PHY’s. It is intended to assist companies in testing transmitter signal quality and receiver sensitivity for either hosts or peripherals.
The kit contains five test fixtures and one 5-Volt DC power supply to provide V-Bus to peripherals. The fixtures consist of:
qty 2 – Host Test Fixtures
qty 2 – Device Test Fixtures
qty 1 – Device Calibration Fixture
qty 1 – Cable Assembly to be used in conjunction with the fixtures. Includes a USB 3.0 Standard A to Standard B (3 meter + 1 meter), Standard A to Standard B (4 inch) and Standard A to Micro B (4 inch).
Please refer to the topology diagram. For more information, please contact your test equipment vendor or see the Electrical Compliance Specification.
To purchase the USB 3.0 Electrical Test Fixture Kit, please fill out the USB Product Order Form and fax or mail it to the address provided on the form.
USB 3.0 Cable Kit
The USB 3.0 Cable Kit provides five (5) SuperSpeed USB (USB 3.0) cables:
- Standard A to Standard B, 3 meter
- Standard A to Micro B, 1 meter
- Standard A to Standard B, 8 inch
- Standard A to Standard B, 4 inch
- Standard A to Micro B, 4 inch
The USB 3.0 Cable Kit is available for purchase at a cost of US$150 (members) or US$200 (non-members). To purchase this kit, please complete the USB Product Order Form and fax or mail it to the address provided on the form.
USB 3.0 xHCI-based PDK
The USB 3.0 xHCI-based Peripheral Development Kit (PDK) provides a host-side solution from Fresco Logic (FL1100 v1.0) or Renesas. It is intended to assist companies who are developing peripherals. For more information about what is shipped with the USB 3.0 xHCI-based PDK, please click here.
The Fresco Logic PDK and Renesas PDK is available for purchase at a cost of US$800 (members) or US$1,000 (non-members). To purchase the PDK, please complete the USB Product Order Form and fax or mail it to the address provided on the form.
USB Functional Compliance Test Devices
The Functional Compliance Test Devices are designed to meet the requirements set forth in the USB2 Compliance Test Device Functional Specification, Revision 1.0. The test devices are used by the USB2 Transaction Translator Test Suite (USBHTT). The specification for the devices is available at http://developer.intel.com/technology/usb/spec.htm. The devices support a simple vendor command API that allows them to be used to deterministically test a wide variety of USB transfer and protocol scenarios.
To purchase USB Functional Compliance Test Devices, please fill out the USB Product Order Form and fax or mail it to the address provided on the form.
