Closed
Description
Board
ESP32S3 Dev Module
Device Description
ESP32-S3R8
Hardware Configuration
PIN 6 being used for NeoPixel RGB
Version
latest stable Release (if not listed below)
IDE Name
Arduino
Operating System
Windows 11
Flash frequency
80mhz
PSRAM enabled
yes
Upload speed
921600
Description
E (3892) rmt: rmt_new_tx_channel(269): not able to power down in light sleep
[ 3003][E][esp32-hal-rmt.c:548] rmtInit(): GPIO 6 - RMT TX Initialization error.
[ 3020][E][esp.c:81] espShow(): Failed to init RMT TX mode on pin 6
Sketch
// NeoPixel Ring simple sketch (c) 2013 Shae Erisson
// Released under the GPLv3 license to match the rest of the
// Adafruit NeoPixel library
// Simple example
#include <Adafruit_NeoPixel.h>
#ifdef __AVR__
#include <avr/power.h> // Required for 16 MHz Adafruit Trinket
#endif
// Which pin on the Arduino is connected to the NeoPixels?
#define PIN 6 // On Trinket or Gemma, suggest changing this to 1
// How many NeoPixels are attached to the Arduino?
#define NUMPIXELS 1 // Popular NeoPixel ring size
// When setting up the NeoPixel library, we tell it how many pixels,
// and which pin to use to send signals. Note that for older NeoPixel
// strips you might need to change the third parameter -- see the
// strandtest example for more information on possible values.
Adafruit_NeoPixel pixels(NUMPIXELS, PIN, NEO_GRB + NEO_KHZ800);
#define DELAYVAL 500 // Time (in milliseconds) to pause between pixels
void setup() {
// These lines are specifically to support the Adafruit Trinket 5V 16 MHz.
// Any other board, you can remove this part (but no harm leaving it):
#if defined(__AVR_ATtiny85__) && (F_CPU == 16000000)
clock_prescale_set(clock_div_1);
#endif
// END of Trinket-specific code.
pixels.begin(); // INITIALIZE NeoPixel strip object (REQUIRED)
}
void loop() {
pixels.clear(); // Set all pixel colors to 'off'
// The first NeoPixel in a strand is #0, second is 1, all the way up
// to the count of pixels minus one.
for(int i=0; i<NUMPIXELS; i++) { // For each pixel...
// pixels.Color() takes RGB values, from 0,0,0 up to 255,255,255
// Here we're using a moderately bright green color:
pixels.setPixelColor(i, pixels.Color(0, 150, 0));
pixels.show(); // Send the updated pixel colors to the hardware.
delay(DELAYVAL); // Pause before next pass through loop
}
}Debug Message
=========== Before Setup Start ===========
Chip Info:
------------------------------------------
Model : ESP32-S3
Package : 0
Revision : 0.02
Cores : 2
CPU Frequency : 240 MHz
XTAL Frequency : 40 MHz
Features Bitfield : 0x00000012
Embedded Flash : No
Embedded PSRAM : No
2.4GHz WiFi : Yes
Classic BT : No
BT Low Energy : Yes
IEEE 802.15.4 : No
------------------------------------------
INTERNAL Memory Info:
------------------------------------------
Total Size : 391672 B ( 382.5 KB)
Free Bytes : 355280 B ( 347.0 KB)
Allocated Bytes : 31456 B ( 30.7 KB)
Minimum Free Bytes: 350432 B ( 342.2 KB)
Largest Free Block: 286708 B ( 280.0 KB)
------------------------------------------
SPIRAM Memory Info:
------------------------------------------
Total Size : 2097152 B (2048.0 KB)
Free Bytes : 2095104 B (2046.0 KB)
Allocated Bytes : 0 B ( 0.0 KB)
Minimum Free Bytes: 2095104 B (2046.0 KB)
Largest Free Block: 2064372 B (2016.0 KB)
Bus Mode : QSPI
------------------------------------------
Flash Info:
------------------------------------------
Chip Size : 8388608 B (8 MB)
Block Size : 65536 B ( 64.0 KB)
Sector Size : 4096 B ( 4.0 KB)
Page Size : 256 B ( 0.2 KB)
Bus Speed : 80 MHz
Bus Mode : QIO
------------------------------------------
Partitions Info:
------------------------------------------
nvs : addr: 0x00009000, size: 20.0 KB, type: DATA, subtype: NVS
otadata : addr: 0x0000E000, size: 8.0 KB, type: DATA, subtype: OTA
app0 : addr: 0x00010000, size: 1920.0 KB, type: APP, subtype: OTA_0
app1 : addr: 0x001F0000, size: 1920.0 KB, type: APP, subtype: OTA_1
spiffs : addr: 0x003D0000, size: 128.0 KB, type: DATA, subtype: SPIFFS
coredump : addr: 0x003F0000, size: 64.0 KB, type: DATA, subtype: COREDUMP
Software Info:
------------------------------------------
Compile Date/Time : Apr 4 2025 14:59:42
Compile Host OS : windows
ESP-IDF Version : v5.4.1-1-g2f7dcd862a-dirty
Arduino Version : 3.2.0
------------------------------------------
Board Info:
------------------------------------------
Arduino Board : ESP32S3_DEV
Arduino Variant : esp32s3
Arduino FQBN : esp32:esp32:esp32s3:UploadSpeed=921600,USBMode=hwcdc,CDCOnBoot=default,MSCOnBoot=default,DFUOnBoot=default,UploadMode=default,CPUFreq=240,FlashMode=qio,FlashSize=8M,PartitionScheme=min_spiffs,DebugLevel=debug,PSRAM=enabled,LoopCore=1,EventsCore=1,EraseFlash=all,JTAGAdapter=default,ZigbeeMode=default
============ Before Setup End ============
=========== Before Setup Start ===========
Chip Info:
------------------------------------------
Model : ESP32-S3
Package : 0
Revision : 0.02
Cores : 2
CPU Frequency : 240 MHz
XTAL Frequency : 40 MHz
Features Bitfield : 0x00000012
Embedded Flash : No
Embedded PSRAM : No
2.4GHz WiFi : Yes
> =========== After Setup Start ============
INTERNAL Memory Info:
------------------------------------------
Total Size : 296232 B ( 289.3 KB)
Free Bytes : 239300 B ( 233.7 KB)
Allocated Bytes : 51516 B ( 50.3 KB)
Minimum Free Bytes: 187472 B ( 183.1 KB)
Largest Free Block: 122868 B ( 120.0 KB)
------------------------------------------
SPIRAM Memory Info:
------------------------------------------
Total Size : 2097152 B (2048.0 KB)
Free Bytes : 2090668 B (2041.7 KB)
Allocated Bytes : 3908 B ( 3.8 KB)
Minimum Free Bytes: 2062916 B (2014.6 KB)
Largest Free Block: 2064372 B (2016.0 KB)
Other Steps to Reproduce
No response
I have checked existing issues, online documentation and the Troubleshooting Guide
- I confirm I have checked existing issues, online documentation and Troubleshooting guide.