#include <Matter.h>

#include <WiFiProv.h>

#include <WiFi.h>

#if !CONFIG_BLUEDROID_ENABLED

#define USE_SOFT_AP // ESP32-S2 has no BLE, therefore, it shall use SoftAP Provisioning

#endif

const char *pop = "abcd1234"; // Proof of possession - otherwise called a PIN - string provided by the device, entered by the user in the phone app

const char *service_name = "PROV_123"; // Name of your device (the Espressif apps expects by default device name starting with "Prov_")

const char *service_key = NULL; // Password used for SofAP method (NULL = no password needed)

bool reset_provisioned = true; // When true the library will automatically delete previously provisioned data.

MatterOnOffLight OnOffLight;

#ifdef LED_BUILTIN

const uint8_t ledPin = LED_BUILTIN;

#else

const uint8_t ledPin = 2; // Set your pin here if your board has not defined LED_BUILTIN

#endif

bool matterCB(bool state) {

digitalWrite(ledPin, state ? HIGH : LOW);

// This callback must return the success state to Matter core

return true;

}

void setup() {

Serial.begin(115200);

// Initialize the LED GPIO

pinMode(ledPin, OUTPUT);

WiFi.begin(); // no SSID/PWD - get it from the Provisioning APP or from NVS (last successful connection)

// BLE Provisioning using the ESP SoftAP Prov works fine for any BLE SoC, including ESP32, ESP32S3 and ESP32C3.

#if CONFIG_BLUEDROID_ENABLED && !defined(USE_SOFT_AP)

Serial.println("Begin Provisioning using BLE");

// Sample uuid that user can pass during provisioning using BLE

uint8_t uuid[16] = {0xb4, 0xdf, 0x5a, 0x1c, 0x3f, 0x6b, 0xf4, 0xbf, 0xea, 0x4a, 0x82, 0x03, 0x04, 0x90, 0x1a, 0x02};

WiFiProv.beginProvision(

NETWORK_PROV_SCHEME_BLE, NETWORK_PROV_SCHEME_HANDLER_FREE_BLE, NETWORK_PROV_SECURITY_1, pop, service_name, service_key, uuid, reset_provisioned

);

Serial.println("You may use this BLE QRCode:");

WiFiProv.printQR(service_name, pop, "ble");

#else

Serial.println("Begin Provisioning using Soft AP");

WiFiProv.beginProvision(NETWORK_PROV_SCHEME_SOFTAP, NETWORK_PROV_SCHEME_HANDLER_NONE, NETWORK_PROV_SECURITY_1, pop, service_name, service_key);

Serial.println("You may use this WiFi QRCode:");

WiFiProv.printQR(service_name, pop, "softap");

#endif

// Wait for WiFi connection

uint32_t counter = 0;

while (WiFi.status() != WL_CONNECTED) {

// resets the device after 10 minutes

if (counter > 2 * 60 * 10) {

Serial.println("\r\n================================================");

Serial.println("Already 10 minutes past. The device will reboot.");

Serial.println("================================================\r\n");

Serial.flush(); // wait until the Serial has sent the whole message.

ESP.restart();

}

// WiFi searching feedback

Serial.print(".");

delay(500);

// adds a new line every 30 seconds

counter++;

if (!(counter % 60)) {

Serial.println();

}

}

// WiFi shall be connected by now

Serial.println();

// Initialize at least one Matter EndPoint

OnOffLight.begin();

// Associate a callback to the Matter Controller

OnOffLight.onChange(matterCB);

// Matter beginning - Last step, after all EndPoints are initialized

Matter.begin();

while (!Matter.isDeviceCommissioned()) {

Serial.println("Matter Node is not commissioned yet.");

Serial.println("Initiate the device discovery in your Matter environment.");

Serial.println("Commission it to your Matter hub with the manual pairing code or QR code");

Serial.printf("Manual pairing code: %s\r\n", Matter.getManualPairingCode().c_str());

Serial.printf("QR code URL: %s\r\n", Matter.getOnboardingQRCodeUrl().c_str());

Serial.println();

// waits 30 seconds for Matter Commissioning, keeping it blocked until done

delay(30000);

}

}

void loop() {

delay(500);

}

{

"fqbn_append": "PartitionScheme=huge_app",

"requires": [

"CONFIG_SOC_WIFI_SUPPORTED=y",

"CONFIG_ESP_MATTER_ENABLE_DATA_MODEL=y"

]

}