adrian-the-git
diff --git a/‎docs/source/tutorials/blink.rst
Copy file name to clipboard
+109Lines changed: 109 additions & 0 deletions b/‎docs/source/tutorials/blink.rst
Copy file name to clipboard
+109Lines changed: 109 additions & 0 deletions
diff --git a/‎docs/source/tutorials/tutorials.rst
Copy file name to clipboardExpand all lines: docs/source/tutorials/tutorials.rst
+1Lines changed: 1 addition & 0 deletions b/‎docs/source/tutorials/tutorials.rst
Copy file name to clipboardExpand all lines: docs/source/tutorials/tutorials.rst
+1Lines changed: 1 addition & 0 deletions
@@ -0,0 +1,109 @@
+##########################
+Blink Interactive Tutorial
+##########################
+
+Introduction
+------------
+
+This is the interactive blink tutorial using `Wokwi`_. For this tutorial you don't need the ESP32 board or the Arduino toolchain.
+
+.. note:: If you don't want to use this tutorial with the simulation, you can copy and paste the code from `Wokwi`_ editor and use on the Arduino IDE or PlatformIO.
+
+About this Tutorial
+-------------------
+
+This tutorial is the most basic for any getting started. In this tutorial, we will show how to set a GPIO pin as output to drive a LED to blink each 1 second.
+
+Step by step
+------------
+
+In order to make this simple blink tutorial, you'll need to do the following steps.
+
+1. Define the GPIO for the LED.
+
+.. code-block::
+
+    #define LED 2
+
+This ``#define LED 2`` will be used to set the GPIO2 as the ``LED`` output pin. 
+
+2. Setup.
+
+Inside the ``setup()`` function, we need to add all things we want to run once during the startup.
+Here we'll add the ``pinMode`` function to set the pin as output.
+
+.. code-block::
+
+    void setup() {
+        pinMode(LED, OUTPUT);
+    }
+
+The first argument is the GPIO number, already defined and the second is the mode, here defined as output.
+
+3. Main Loop.
+
+After the ``setup``, the code runs the ``loop`` function infinitely. Here we will handle the GPIO in order to get the LED blinking.
+
+.. code-block::
+
+    void loop() {
+        digitalWrite(LED, HIGH);
+        delay(100);
+        digitalWrite(LED, LOW);
+        delay(100);
+    }
+
+The first function is the ``digitalWrite()`` with two arguments:
+
+* GPIO: Set the GPIO pin. Here defined by our ``LED`` connected to the GPIO2.
+* State: Set the GPIO state as HIGH (on) or LOW (off).
+
+This first ``digitalWrite`` we will set the LED on.
+
+After the ``digitalWrite``, we will set a ``delay`` function in order to wait for some time, defined in milliseconds.
+
+Now we can set the GPIO to ``LOW`` to turn the LED off and ``delay`` for more few milliseconds to get the LED blinking.
+
+4. Run the code.
+
+To run this code, you'll need a development board and the Arduino toolchain installed in your computer. If you don't have both, you can use the simulator to test and edit the code.
+
+Simulation
+----------
+
+This simulator is provided by `Wokwi`_ and you can test the blink code and play with some modification to learn mode about this example.
+
+.. raw:: html
+
+    <iframe src="https://wokwi.com/arduino/projects/305566932847821378?embed=1" width="100%" height="400" border="0"></iframe>
+
+Change the parameters, like the delay period, to test the code right on your browser. You can add more LEDs, change the GPIO and more.
+
+Code
+----
+
+Here is the full blink code.
+
+.. code-block::
+
+    #define LED 2
+
+    void setup() {
+        pinMode(LED, OUTPUT);
+    }
+
+    void loop() {
+        digitalWrite(LED, HIGH);
+        delay(100);
+        digitalWrite(LED, LOW);
+        delay(100);
+    }
+
+Resources
+---------
+
+* `ESP32 Datasheet`_ (Datasheet)
+* `Wokwi`_ (Wokwi Website)
+
+.. _ESP32 Datasheet: https://www.espressif.com/sites/default/files/documentation/esp32_datasheet_en.pdf
+.. _Wokwi: https://wokwi.com/
@@ -6,6 +6,7 @@ Tutorials
     :maxdepth: 2
     :caption: Tutorials:
 
+    Blink <blink>
     Basic <basic>
     DFU <dfu>
     GPIO Matrix and Pin Mux <io_mux>