1#ifndef NETDEV_PCS_H
2#define NETDEV_PCS_H
3
4#include <linux/phy.h>
5#include <linux/spinlock.h>
6#include <linux/workqueue.h>
7
8#include <net/eee.h>
9
10struct device_node;
11struct ethtool_cmd;
12struct fwnode_handle;
13struct net_device;
14struct phylink;
15
16enum {
17 MLO_PAUSE_NONE,
18 MLO_PAUSE_RX = BIT(0),
19 MLO_PAUSE_TX = BIT(1),
20 MLO_PAUSE_TXRX_MASK = MLO_PAUSE_TX | MLO_PAUSE_RX,
21 MLO_PAUSE_AN = BIT(2),
22
23 MLO_AN_PHY = 0, /* Conventional PHY */
24 MLO_AN_FIXED, /* Fixed-link mode */
25 MLO_AN_INBAND, /* In-band protocol */
26
27 /* PCS "negotiation" mode.
28 * PHYLINK_PCS_NEG_NONE - protocol has no inband capability
29 * PHYLINK_PCS_NEG_OUTBAND - some out of band or fixed link setting
30 * PHYLINK_PCS_NEG_INBAND_DISABLED - inband mode disabled, e.g.
31 * 1000base-X with autoneg off
32 * PHYLINK_PCS_NEG_INBAND_ENABLED - inband mode enabled
33 * Additionally, this can be tested using bitmasks:
34 * PHYLINK_PCS_NEG_INBAND - inband mode selected
35 * PHYLINK_PCS_NEG_ENABLED - negotiation mode enabled
36 */
37 PHYLINK_PCS_NEG_NONE = 0,
38 PHYLINK_PCS_NEG_ENABLED = BIT(4),
39 PHYLINK_PCS_NEG_OUTBAND = BIT(5),
40 PHYLINK_PCS_NEG_INBAND = BIT(6),
41 PHYLINK_PCS_NEG_INBAND_DISABLED = PHYLINK_PCS_NEG_INBAND,
42 PHYLINK_PCS_NEG_INBAND_ENABLED = PHYLINK_PCS_NEG_INBAND |
43 PHYLINK_PCS_NEG_ENABLED,
44
45 /* MAC_SYM_PAUSE and MAC_ASYM_PAUSE are used when configuring our
46 * autonegotiation advertisement. They correspond to the PAUSE and
47 * ASM_DIR bits defined by 802.3, respectively.
48 *
49 * The following table lists the values of tx_pause and rx_pause which
50 * might be requested in mac_link_up. The exact values depend on either
51 * the results of autonegotation (if MLO_PAUSE_AN is set) or user
52 * configuration (if MLO_PAUSE_AN is not set).
53 *
54 * MAC_SYM_PAUSE MAC_ASYM_PAUSE MLO_PAUSE_AN tx_pause/rx_pause
55 * ============= ============== ============ ==================
56 * 0 0 0 0/0
57 * 0 0 1 0/0
58 * 0 1 0 0/0, 0/1, 1/0, 1/1
59 * 0 1 1 0/0, 1/0
60 * 1 0 0 0/0, 1/1
61 * 1 0 1 0/0, 1/1
62 * 1 1 0 0/0, 0/1, 1/0, 1/1
63 * 1 1 1 0/0, 0/1, 1/1
64 *
65 * If you set MAC_ASYM_PAUSE, the user may request any combination of
66 * tx_pause and rx_pause. You do not have to support these
67 * combinations.
68 *
69 * However, you should support combinations of tx_pause and rx_pause
70 * which might be the result of autonegotation. For example, don't set
71 * MAC_SYM_PAUSE unless your device can support tx_pause and rx_pause
72 * at the same time.
73 */
74 MAC_SYM_PAUSE = BIT(0),
75 MAC_ASYM_PAUSE = BIT(1),
76 MAC_10HD = BIT(2),
77 MAC_10FD = BIT(3),
78 MAC_10 = MAC_10HD | MAC_10FD,
79 MAC_100HD = BIT(4),
80 MAC_100FD = BIT(5),
81 MAC_100 = MAC_100HD | MAC_100FD,
82 MAC_1000HD = BIT(6),
83 MAC_1000FD = BIT(7),
84 MAC_1000 = MAC_1000HD | MAC_1000FD,
85 MAC_2500FD = BIT(8),
86 MAC_5000FD = BIT(9),
87 MAC_10000FD = BIT(10),
88 MAC_20000FD = BIT(11),
89 MAC_25000FD = BIT(12),
90 MAC_40000FD = BIT(13),
91 MAC_50000FD = BIT(14),
92 MAC_56000FD = BIT(15),
93 MAC_100000FD = BIT(16),
94 MAC_200000FD = BIT(17),
95 MAC_400000FD = BIT(18),
96};
97
98static inline bool phylink_autoneg_inband(unsigned int mode)
99{
100 return mode == MLO_AN_INBAND;
101}
102
103/**
104 * struct phylink_link_state - link state structure
105 * @advertising: ethtool bitmask containing advertised link modes
106 * @lp_advertising: ethtool bitmask containing link partner advertised link
107 * modes
108 * @interface: link &typedef phy_interface_t mode
109 * @speed: link speed, one of the SPEED_* constants.
110 * @duplex: link duplex mode, one of DUPLEX_* constants.
111 * @pause: link pause state, described by MLO_PAUSE_* constants.
112 * @rate_matching: rate matching being performed, one of the RATE_MATCH_*
113 * constants. If rate matching is taking place, then the speed/duplex of
114 * the medium link mode (@speed and @duplex) and the speed/duplex of the phy
115 * interface mode (@interface) are different.
116 * @link: true if the link is up.
117 * @an_complete: true if autonegotiation has completed.
118 */
119struct phylink_link_state {
120 __ETHTOOL_DECLARE_LINK_MODE_MASK(advertising);
121 __ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising);
122 phy_interface_t interface;
123 int speed;
124 int duplex;
125 int pause;
126 int rate_matching;
127 unsigned int link:1;
128 unsigned int an_complete:1;
129};
130
131enum phylink_op_type {
132 PHYLINK_NETDEV = 0,
133 PHYLINK_DEV,
134};
135
136/**
137 * struct phylink_config - PHYLINK configuration structure
138 * @dev: a pointer to a struct device associated with the MAC
139 * @type: operation type of PHYLINK instance
140 * @poll_fixed_state: if true, starts link_poll,
141 * if MAC link is at %MLO_AN_FIXED mode.
142 * @mac_managed_pm: if true, indicate the MAC driver is responsible for PHY PM.
143 * @mac_requires_rxc: if true, the MAC always requires a receive clock from PHY.
144 * The PHY driver should start the clock signal as soon as
145 * possible and avoid stopping it during suspend events.
146 * @default_an_inband: if true, defaults to MLO_AN_INBAND rather than
147 * MLO_AN_PHY. A fixed-link specification will override.
148 * @eee_rx_clk_stop_enable: if true, PHY can stop the receive clock during LPI
149 * @get_fixed_state: callback to execute to determine the fixed link state,
150 * if MAC link is at %MLO_AN_FIXED mode.
151 * @supported_interfaces: bitmap describing which PHY_INTERFACE_MODE_xxx
152 * are supported by the MAC/PCS.
153 * @lpi_interfaces: bitmap describing which PHY interface modes can support
154 * LPI signalling.
155 * @mac_capabilities: MAC pause/speed/duplex capabilities.
156 * @lpi_capabilities: MAC speeds which can support LPI signalling
157 * @lpi_timer_default: Default EEE LPI timer setting.
158 * @eee_enabled_default: If set, EEE will be enabled by phylink at creation time
159 */
160struct phylink_config {
161 struct device *dev;
162 enum phylink_op_type type;
163 bool poll_fixed_state;
164 bool mac_managed_pm;
165 bool mac_requires_rxc;
166 bool default_an_inband;
167 bool eee_rx_clk_stop_enable;
168 void (*get_fixed_state)(struct phylink_config *config,
169 struct phylink_link_state *state);
170 DECLARE_PHY_INTERFACE_MASK(supported_interfaces);
171 DECLARE_PHY_INTERFACE_MASK(lpi_interfaces);
172 unsigned long mac_capabilities;
173 unsigned long lpi_capabilities;
174 u32 lpi_timer_default;
175 bool eee_enabled_default;
176};
177
178void phylink_limit_mac_speed(struct phylink_config *config, u32 max_speed);
179
180/**
181 * struct phylink_mac_ops - MAC operations structure.
182 * @mac_get_caps: Get MAC capabilities for interface mode.
183 * @mac_select_pcs: Select a PCS for the interface mode.
184 * @mac_prepare: prepare for a major reconfiguration of the interface.
185 * @mac_config: configure the MAC for the selected mode and state.
186 * @mac_finish: finish a major reconfiguration of the interface.
187 * @mac_link_down: take the link down.
188 * @mac_link_up: allow the link to come up.
189 * @mac_disable_tx_lpi: disable LPI.
190 * @mac_enable_tx_lpi: enable and configure LPI.
191 *
192 * The individual methods are described more fully below.
193 */
194struct phylink_mac_ops {
195 unsigned long (*mac_get_caps)(struct phylink_config *config,
196 phy_interface_t interface);
197 struct phylink_pcs *(*mac_select_pcs)(struct phylink_config *config,
198 phy_interface_t interface);
199 int (*mac_prepare)(struct phylink_config *config, unsigned int mode,
200 phy_interface_t iface);
201 void (*mac_config)(struct phylink_config *config, unsigned int mode,
202 const struct phylink_link_state *state);
203 int (*mac_finish)(struct phylink_config *config, unsigned int mode,
204 phy_interface_t iface);
205 void (*mac_link_down)(struct phylink_config *config, unsigned int mode,
206 phy_interface_t interface);
207 void (*mac_link_up)(struct phylink_config *config,
208 struct phy_device *phy, unsigned int mode,
209 phy_interface_t interface, int speed, int duplex,
210 bool tx_pause, bool rx_pause);
211 void (*mac_disable_tx_lpi)(struct phylink_config *config);
212 int (*mac_enable_tx_lpi)(struct phylink_config *config, u32 timer,
213 bool tx_clk_stop);
214};
215
216#if 0 /* For kernel-doc purposes only. */
217/**
218 * mac_get_caps: Get MAC capabilities for interface mode.
219 * @config: a pointer to a &struct phylink_config.
220 * @interface: PHY interface mode.
221 *
222 * Optional method. When not provided, config->mac_capabilities will be used.
223 * When implemented, this returns the MAC capabilities for the specified
224 * interface mode where there is some special handling required by the MAC
225 * driver (e.g. not supporting half-duplex in certain interface modes.)
226 */
227unsigned long mac_get_caps(struct phylink_config *config,
228 phy_interface_t interface);
229/**
230 * mac_select_pcs: Select a PCS for the interface mode.
231 * @config: a pointer to a &struct phylink_config.
232 * @interface: PHY interface mode for PCS
233 *
234 * Return the &struct phylink_pcs for the specified interface mode, or
235 * NULL if none is required, or an error pointer on error.
236 *
237 * This must not modify any state. It is used to query which PCS should
238 * be used. Phylink will use this during validation to ensure that the
239 * configuration is valid, and when setting a configuration to internally
240 * set the PCS that will be used.
241 */
242struct phylink_pcs *mac_select_pcs(struct phylink_config *config,
243 phy_interface_t interface);
244
245/**
246 * mac_prepare() - prepare to change the PHY interface mode
247 * @config: a pointer to a &struct phylink_config.
248 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
249 * @iface: interface mode to switch to
250 *
251 * phylink will call this method at the beginning of a full initialisation
252 * of the link, which includes changing the interface mode or at initial
253 * startup time. It may be called for the current mode. The MAC driver
254 * should perform whatever actions are required, e.g. disabling the
255 * Serdes PHY.
256 *
257 * This will be the first call in the sequence:
258 * - mac_prepare()
259 * - mac_config()
260 * - pcs_config()
261 * - possible pcs_an_restart()
262 * - mac_finish()
263 *
264 * Returns zero on success, or negative errno on failure which will be
265 * reported to the kernel log.
266 */
267int mac_prepare(struct phylink_config *config, unsigned int mode,
268 phy_interface_t iface);
269
270/**
271 * mac_config() - configure the MAC for the selected mode and state
272 * @config: a pointer to a &struct phylink_config.
273 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
274 * @state: a pointer to a &struct phylink_link_state.
275 *
276 * Note - not all members of @state are valid. In particular,
277 * @state->lp_advertising, @state->link, @state->an_complete are never
278 * guaranteed to be correct, and so any mac_config() implementation must
279 * never reference these fields.
280 *
281 * This will only be called to reconfigure the MAC for a "major" change in
282 * e.g. interface mode. It will not be called for changes in speed, duplex
283 * or pause modes or to change the in-band advertisement.
284 *
285 * In all negotiation modes, as defined by @mode, @state->pause indicates the
286 * pause settings which should be applied as follows. If %MLO_PAUSE_AN is not
287 * set, %MLO_PAUSE_TX and %MLO_PAUSE_RX indicate whether the MAC should send
288 * pause frames and/or act on received pause frames respectively. Otherwise,
289 * the results of in-band negotiation/status from the MAC PCS should be used
290 * to control the MAC pause mode settings.
291 *
292 * The action performed depends on the currently selected mode:
293 *
294 * %MLO_AN_FIXED, %MLO_AN_PHY:
295 * Configure for non-inband negotiation mode, where the link settings
296 * are completely communicated via mac_link_up(). The physical link
297 * protocol from the MAC is specified by @state->interface.
298 *
299 * @state->advertising may be used, but is not required.
300 *
301 * Older drivers (prior to the mac_link_up() change) may use @state->speed,
302 * @state->duplex and @state->pause to configure the MAC, but this is
303 * deprecated; such drivers should be converted to use mac_link_up().
304 *
305 * Other members of @state must be ignored.
306 *
307 * Valid state members: interface, advertising.
308 * Deprecated state members: speed, duplex, pause.
309 *
310 * %MLO_AN_INBAND:
311 * place the link in an inband negotiation mode (such as 802.3z
312 * 1000base-X or Cisco SGMII mode depending on the @state->interface
313 * mode). In both cases, link state management (whether the link
314 * is up or not) is performed by the MAC, and reported via the
315 * pcs_get_state() callback. Changes in link state must be made
316 * by calling phylink_mac_change().
317 *
318 * Interface mode specific details are mentioned below.
319 *
320 * If in 802.3z mode, the link speed is fixed, dependent on the
321 * @state->interface. Duplex and pause modes are negotiated via
322 * the in-band configuration word. Advertised pause modes are set
323 * according to the @state->an_enabled and @state->advertising
324 * flags. Beware of MACs which only support full duplex at gigabit
325 * and higher speeds.
326 *
327 * If in Cisco SGMII mode, the link speed and duplex mode are passed
328 * in the serial bitstream 16-bit configuration word, and the MAC
329 * should be configured to read these bits and acknowledge the
330 * configuration word. Nothing is advertised by the MAC. The MAC is
331 * responsible for reading the configuration word and configuring
332 * itself accordingly.
333 *
334 * Valid state members: interface, an_enabled, pause, advertising.
335 *
336 * Implementations are expected to update the MAC to reflect the
337 * requested settings - i.o.w., if nothing has changed between two
338 * calls, no action is expected. If only flow control settings have
339 * changed, flow control should be updated *without* taking the link
340 * down. This "update" behaviour is critical to avoid bouncing the
341 * link up status.
342 */
343void mac_config(struct phylink_config *config, unsigned int mode,
344 const struct phylink_link_state *state);
345
346/**
347 * mac_finish() - finish a to change the PHY interface mode
348 * @config: a pointer to a &struct phylink_config.
349 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
350 * @iface: interface mode to switch to
351 *
352 * phylink will call this if it called mac_prepare() to allow the MAC to
353 * complete any necessary steps after the MAC and PCS have been configured
354 * for the @mode and @iface. E.g. a MAC driver may wish to re-enable the
355 * Serdes PHY here if it was previously disabled by mac_prepare().
356 *
357 * Returns zero on success, or negative errno on failure which will be
358 * reported to the kernel log.
359 */
360int mac_finish(struct phylink_config *config, unsigned int mode,
361 phy_interface_t iface);
362
363/**
364 * mac_link_down() - notification that the link has gone down
365 * @config: a pointer to a &struct phylink_config.
366 * @mode: link autonegotiation mode
367 * @interface: link &typedef phy_interface_t mode
368 *
369 * Notifies the MAC that the link has gone down. This will not be called
370 * unless mac_link_up() has been previously called.
371 *
372 * The MAC should stop processing packets for transmission and reception.
373 * phylink will have called netif_carrier_off() to notify the networking
374 * stack that the link has gone down, so MAC drivers should not make this
375 * call.
376 *
377 * If @mode is %MLO_AN_INBAND, then this function must not prevent the
378 * link coming up.
379 */
380void mac_link_down(struct phylink_config *config, unsigned int mode,
381 phy_interface_t interface);
382
383/**
384 * mac_link_up() - notification that the link has come up
385 * @config: a pointer to a &struct phylink_config.
386 * @phy: any attached phy (deprecated - please use LPI interfaces)
387 * @mode: link autonegotiation mode
388 * @interface: link &typedef phy_interface_t mode
389 * @speed: link speed
390 * @duplex: link duplex
391 * @tx_pause: link transmit pause enablement status
392 * @rx_pause: link receive pause enablement status
393 *
394 * Notifies the MAC that the link has come up, and the parameters of the
395 * link as seen from the MACs point of view. If mac_link_up() has been
396 * called previously, there will be an intervening call to mac_link_down()
397 * before this method will be subsequently called.
398 *
399 * @speed, @duplex, @tx_pause and @rx_pause indicate the finalised link
400 * settings, and should be used to configure the MAC block appropriately
401 * where these settings are not automatically conveyed from the PCS block,
402 * or if in-band negotiation (as defined by phylink_autoneg_inband(@mode))
403 * is disabled.
404 *
405 * Note that when 802.3z in-band negotiation is in use, it is possible
406 * that the user wishes to override the pause settings, and this should
407 * be allowed when considering the implementation of this method.
408 *
409 * Once configured, the MAC may begin to process packets for transmission
410 * and reception.
411 *
412 * Interface type selection must be done in mac_config().
413 */
414void mac_link_up(struct phylink_config *config, struct phy_device *phy,
415 unsigned int mode, phy_interface_t interface,
416 int speed, int duplex, bool tx_pause, bool rx_pause);
417
418/**
419 * mac_disable_tx_lpi() - disable LPI generation at the MAC
420 * @config: a pointer to a &struct phylink_config.
421 *
422 * Disable generation of LPI at the MAC, effectively preventing the MAC
423 * from indicating that it is idle.
424 */
425void mac_disable_tx_lpi(struct phylink_config *config);
426
427/**
428 * mac_enable_tx_lpi() - configure and enable LPI generation at the MAC
429 * @config: a pointer to a &struct phylink_config.
430 * @timer: LPI timeout in microseconds.
431 * @tx_clk_stop: allow xMII transmit clock to be stopped during LPI
432 *
433 * Configure the LPI timeout accordingly. This will only be called when
434 * the link is already up, to cater for situations where the hardware
435 * needs to be programmed according to the link speed.
436 *
437 * Enable LPI generation at the MAC, and configure whether the xMII transmit
438 * clock may be stopped.
439 *
440 * Returns: 0 on success. Please consult with rmk before returning an error.
441 */
442int mac_enable_tx_lpi(struct phylink_config *config, u32 timer,
443 bool tx_clk_stop);
444#endif
445
446struct phylink_pcs_ops;
447
448/**
449 * struct phylink_pcs - PHYLINK PCS instance
450 * @supported_interfaces: describing which PHY_INTERFACE_MODE_xxx
451 * are supported by this PCS.
452 * @ops: a pointer to the &struct phylink_pcs_ops structure
453 * @phylink: pointer to &struct phylink_config
454 * @poll: poll the PCS for link changes
455 * @rxc_always_on: The MAC driver requires the reference clock
456 * to always be on. Standalone PCS drivers which
457 * do not have access to a PHY device can check
458 * this instead of PHY_F_RXC_ALWAYS_ON.
459 *
460 * This structure is designed to be embedded within the PCS private data,
461 * and will be passed between phylink and the PCS.
462 *
463 * The @phylink member is private to phylink and must not be touched by
464 * the PCS driver.
465 */
466struct phylink_pcs {
467 DECLARE_PHY_INTERFACE_MASK(supported_interfaces);
468 const struct phylink_pcs_ops *ops;
469 struct phylink *phylink;
470 bool poll;
471 bool rxc_always_on;
472};
473
474/**
475 * struct phylink_pcs_ops - MAC PCS operations structure.
476 * @pcs_validate: validate the link configuration.
477 * @pcs_inband_caps: query inband support for interface mode.
478 * @pcs_enable: enable the PCS.
479 * @pcs_disable: disable the PCS.
480 * @pcs_pre_config: pre-mac_config method (for errata)
481 * @pcs_post_config: post-mac_config method (for arrata)
482 * @pcs_get_state: read the current MAC PCS link state from the hardware.
483 * @pcs_config: configure the MAC PCS for the selected mode and state.
484 * @pcs_an_restart: restart 802.3z BaseX autonegotiation.
485 * @pcs_link_up: program the PCS for the resolved link configuration
486 * (where necessary).
487 * @pcs_disable_eee: optional notification to PCS that EEE has been disabled
488 * at the MAC.
489 * @pcs_enable_eee: optional notification to PCS that EEE will be enabled at
490 * the MAC.
491 * @pcs_pre_init: configure PCS components necessary for MAC hardware
492 * initialization e.g. RX clock for stmmac.
493 */
494struct phylink_pcs_ops {
495 int (*pcs_validate)(struct phylink_pcs *pcs, unsigned long *supported,
496 const struct phylink_link_state *state);
497 unsigned int (*pcs_inband_caps)(struct phylink_pcs *pcs,
498 phy_interface_t interface);
499 int (*pcs_enable)(struct phylink_pcs *pcs);
500 void (*pcs_disable)(struct phylink_pcs *pcs);
501 void (*pcs_pre_config)(struct phylink_pcs *pcs,
502 phy_interface_t interface);
503 int (*pcs_post_config)(struct phylink_pcs *pcs,
504 phy_interface_t interface);
505 void (*pcs_get_state)(struct phylink_pcs *pcs, unsigned int neg_mode,
506 struct phylink_link_state *state);
507 int (*pcs_config)(struct phylink_pcs *pcs, unsigned int neg_mode,
508 phy_interface_t interface,
509 const unsigned long *advertising,
510 bool permit_pause_to_mac);
511 void (*pcs_an_restart)(struct phylink_pcs *pcs);
512 void (*pcs_link_up)(struct phylink_pcs *pcs, unsigned int neg_mode,
513 phy_interface_t interface, int speed, int duplex);
514 void (*pcs_disable_eee)(struct phylink_pcs *pcs);
515 void (*pcs_enable_eee)(struct phylink_pcs *pcs);
516 int (*pcs_pre_init)(struct phylink_pcs *pcs);
517};
518
519#if 0 /* For kernel-doc purposes only. */
520/**
521 * pcs_validate() - validate the link configuration.
522 * @pcs: a pointer to a &struct phylink_pcs.
523 * @supported: ethtool bitmask for supported link modes.
524 * @state: a const pointer to a &struct phylink_link_state.
525 *
526 * Validate the interface mode, and advertising's autoneg bit, removing any
527 * media ethtool link modes that would not be supportable from the supported
528 * mask. Phylink will propagate the changes to the advertising mask. See the
529 * &struct phylink_mac_ops validate() method.
530 *
531 * Returns -EINVAL if the interface mode/autoneg mode is not supported.
532 * Returns non-zero positive if the link state can be supported.
533 */
534int pcs_validate(struct phylink_pcs *pcs, unsigned long *supported,
535 const struct phylink_link_state *state);
536
537/**
538 * pcs_inband_caps - query PCS in-band capabilities for interface mode.
539 * @pcs: a pointer to a &struct phylink_pcs.
540 * @interface: interface mode to be queried
541 *
542 * Returns zero if it is unknown what in-band signalling is supported by the
543 * PHY (e.g. because the PHY driver doesn't implement the method.) Otherwise,
544 * returns a bit mask of the LINK_INBAND_* values from
545 * &enum link_inband_signalling to describe which inband modes are supported
546 * for this interface mode.
547 */
548unsigned int pcs_inband_caps(struct phylink_pcs *pcs,
549 phy_interface_t interface);
550
551/**
552 * pcs_enable() - enable the PCS.
553 * @pcs: a pointer to a &struct phylink_pcs.
554 */
555int pcs_enable(struct phylink_pcs *pcs);
556
557/**
558 * pcs_disable() - disable the PCS.
559 * @pcs: a pointer to a &struct phylink_pcs.
560 */
561void pcs_disable(struct phylink_pcs *pcs);
562
563/**
564 * pcs_get_state() - Read the current inband link state from the hardware
565 * @pcs: a pointer to a &struct phylink_pcs.
566 * @neg_mode: link negotiation mode (PHYLINK_PCS_NEG_xxx)
567 * @state: a pointer to a &struct phylink_link_state.
568 *
569 * Read the current inband link state from the MAC PCS, reporting the
570 * current speed in @state->speed, duplex mode in @state->duplex, pause
571 * mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits,
572 * negotiation completion state in @state->an_complete, and link up state
573 * in @state->link. If possible, @state->lp_advertising should also be
574 * populated.
575 *
576 * Note that the @neg_mode parameter is always the PHYLINK_PCS_NEG_xxx
577 * state, not MLO_AN_xxx.
578 */
579void pcs_get_state(struct phylink_pcs *pcs, unsigned int neg_mode,
580 struct phylink_link_state *state);
581
582/**
583 * pcs_config() - Configure the PCS mode and advertisement
584 * @pcs: a pointer to a &struct phylink_pcs.
585 * @neg_mode: link negotiation mode (see below)
586 * @interface: interface mode to be used
587 * @advertising: adertisement ethtool link mode mask
588 * @permit_pause_to_mac: permit forwarding pause resolution to MAC
589 *
590 * Configure the PCS for the operating mode, the interface mode, and set
591 * the advertisement mask. @permit_pause_to_mac indicates whether the
592 * hardware may forward the pause mode resolution to the MAC.
593 *
594 * When operating in %MLO_AN_INBAND, inband should always be enabled,
595 * otherwise inband should be disabled.
596 *
597 * For SGMII, there is no advertisement from the MAC side, the PCS should
598 * be programmed to acknowledge the inband word from the PHY.
599 *
600 * For 1000BASE-X, the advertisement should be programmed into the PCS.
601 *
602 * For most 10GBASE-R, there is no advertisement.
603 *
604 * The %neg_mode argument should be tested via the phylink_mode_*() family of
605 * functions, or for PCS that set pcs->neg_mode true, should be tested
606 * against the PHYLINK_PCS_NEG_* definitions.
607 *
608 * pcs_config() will be called when configuration of the PCS is required
609 * or when the advertisement is possibly updated. It must not unnecessarily
610 * disrupt an established link.
611 *
612 * When an autonegotiation restart is required for 802.3z modes, .pcs_config()
613 * should return a positive non-zero integer (e.g. 1) to indicate to phylink
614 * to call the pcs_an_restart() method.
615 */
616int pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
617 phy_interface_t interface, const unsigned long *advertising,
618 bool permit_pause_to_mac);
619
620/**
621 * pcs_an_restart() - restart 802.3z BaseX autonegotiation
622 * @pcs: a pointer to a &struct phylink_pcs.
623 *
624 * When PCS ops are present, this overrides mac_an_restart() in &struct
625 * phylink_mac_ops.
626 */
627void pcs_an_restart(struct phylink_pcs *pcs);
628
629/**
630 * pcs_link_up() - program the PCS for the resolved link configuration
631 * @pcs: a pointer to a &struct phylink_pcs.
632 * @neg_mode: link negotiation mode (see below)
633 * @interface: link &typedef phy_interface_t mode
634 * @speed: link speed
635 * @duplex: link duplex
636 *
637 * This call will be made just before mac_link_up() to inform the PCS of
638 * the resolved link parameters. For example, a PCS operating in SGMII
639 * mode without in-band AN needs to be manually configured for the link
640 * and duplex setting. Otherwise, this should be a no-op.
641 *
642 * The %mode argument should be tested via the phylink_mode_*() family of
643 * functions, or for PCS that set pcs->neg_mode true, should be tested
644 * against the PHYLINK_PCS_NEG_* definitions.
645 */
646void pcs_link_up(struct phylink_pcs *pcs, unsigned int neg_mode,
647 phy_interface_t interface, int speed, int duplex);
648
649/**
650 * pcs_disable_eee() - Disable EEE at the PCS
651 * @pcs: a pointer to a &struct phylink_pcs
652 *
653 * Optional method informing the PCS that EEE has been disabled at the MAC.
654 */
655void pcs_disable_eee(struct phylink_pcs *pcs);
656
657/**
658 * pcs_enable_eee() - Enable EEE at the PCS
659 * @pcs: a pointer to a &struct phylink_pcs
660 *
661 * Optional method informing the PCS that EEE is about to be enabled at the MAC.
662 */
663void pcs_enable_eee(struct phylink_pcs *pcs);
664
665/**
666 * pcs_pre_init() - Configure PCS components necessary for MAC initialization
667 * @pcs: a pointer to a &struct phylink_pcs.
668 *
669 * This function can be called by MAC drivers through the
670 * phylink_pcs_pre_init() wrapper, before their hardware is initialized. It
671 * should not be called after the link is brought up, as reconfiguring the PCS
672 * at this point could break the link.
673 *
674 * Some MAC devices require specific hardware initialization to be performed by
675 * their associated PCS device before they can properly initialize their own
676 * hardware. An example of this is the initialization of stmmac controllers,
677 * which requires an active REF_CLK signal to be provided by the PHY/PCS.
678 *
679 * By calling phylink_pcs_pre_init(), MAC drivers can ensure that the PCS is
680 * setup in a way that allows for successful hardware initialization.
681 *
682 * The specific configuration performed by pcs_pre_init() is dependent on the
683 * model of PCS and the requirements of the MAC device attached to it. PCS
684 * driver authors should consider whether their target device is to be used in
685 * conjunction with a MAC device whose driver calls phylink_pcs_pre_init(). MAC
686 * driver authors should document their requirements for the PCS
687 * pre-initialization.
688 *
689 */
690int pcs_pre_init(struct phylink_pcs *pcs);
691
692#endif
693
694struct phylink *phylink_create(struct phylink_config *,
695 const struct fwnode_handle *,
696 phy_interface_t,
697 const struct phylink_mac_ops *);
698void phylink_destroy(struct phylink *);
699bool phylink_expects_phy(struct phylink *pl);
700
701int phylink_connect_phy(struct phylink *, struct phy_device *);
702int phylink_of_phy_connect(struct phylink *, struct device_node *, u32 flags);
703int phylink_fwnode_phy_connect(struct phylink *pl,
704 const struct fwnode_handle *fwnode,
705 u32 flags);
706void phylink_disconnect_phy(struct phylink *);
707int phylink_set_fixed_link(struct phylink *,
708 const struct phylink_link_state *);
709
710void phylink_mac_change(struct phylink *, bool up);
711void phylink_pcs_change(struct phylink_pcs *, bool up);
712
713int phylink_pcs_pre_init(struct phylink *pl, struct phylink_pcs *pcs);
714
715void phylink_start(struct phylink *);
716void phylink_stop(struct phylink *);
717
718void phylink_rx_clk_stop_block(struct phylink *);
719void phylink_rx_clk_stop_unblock(struct phylink *);
720
721void phylink_suspend(struct phylink *pl, bool mac_wol);
722void phylink_prepare_resume(struct phylink *pl);
723void phylink_resume(struct phylink *pl);
724
725void phylink_ethtool_get_wol(struct phylink *, struct ethtool_wolinfo *);
726int phylink_ethtool_set_wol(struct phylink *, struct ethtool_wolinfo *);
727
728int phylink_ethtool_ksettings_get(struct phylink *,
729 struct ethtool_link_ksettings *);
730int phylink_ethtool_ksettings_set(struct phylink *,
731 const struct ethtool_link_ksettings *);
732int phylink_ethtool_nway_reset(struct phylink *);
733void phylink_ethtool_get_pauseparam(struct phylink *,
734 struct ethtool_pauseparam *);
735int phylink_ethtool_set_pauseparam(struct phylink *,
736 struct ethtool_pauseparam *);
737int phylink_get_eee_err(struct phylink *);
738int phylink_ethtool_get_eee(struct phylink *link, struct ethtool_keee *eee);
739int phylink_ethtool_set_eee(struct phylink *link, struct ethtool_keee *eee);
740int phylink_mii_ioctl(struct phylink *, struct ifreq *, int);
741int phylink_speed_down(struct phylink *pl, bool sync);
742int phylink_speed_up(struct phylink *pl);
743
744#define phylink_zero(bm) \
745 bitmap_zero(bm, __ETHTOOL_LINK_MODE_MASK_NBITS)
746#define __phylink_do_bit(op, bm, mode) \
747 op(ETHTOOL_LINK_MODE_ ## mode ## _BIT, bm)
748
749#define phylink_set(bm, mode) __phylink_do_bit(__set_bit, bm, mode)
750#define phylink_clear(bm, mode) __phylink_do_bit(__clear_bit, bm, mode)
751#define phylink_test(bm, mode) __phylink_do_bit(test_bit, bm, mode)
752
753void phylink_set_port_modes(unsigned long *bits);
754
755/**
756 * phylink_get_link_timer_ns - return the PCS link timer value
757 * @interface: link &typedef phy_interface_t mode
758 *
759 * Return the PCS link timer setting in nanoseconds for the PHY @interface
760 * mode, or -EINVAL if not appropriate.
761 */
762static inline int phylink_get_link_timer_ns(phy_interface_t interface)
763{
764 switch (interface) {
765 case PHY_INTERFACE_MODE_SGMII:
766 case PHY_INTERFACE_MODE_QSGMII:
767 case PHY_INTERFACE_MODE_USXGMII:
768 case PHY_INTERFACE_MODE_10G_QXGMII:
769 return 1600000;
770
771 case PHY_INTERFACE_MODE_1000BASEX:
772 case PHY_INTERFACE_MODE_2500BASEX:
773 return 10000000;
774
775 default:
776 return -EINVAL;
777 }
778}
779
780/**
781 * phylink_mac_implements_lpi() - determine if MAC implements LPI ops
782 * @ops: phylink_mac_ops structure
783 *
784 * Returns true if the phylink MAC operations structure indicates that the
785 * LPI operations have been implemented, false otherwise.
786 */
787static inline bool phylink_mac_implements_lpi(const struct phylink_mac_ops *ops)
788{
789 return ops && ops->mac_disable_tx_lpi && ops->mac_enable_tx_lpi;
790}
791
792void phylink_mii_c22_pcs_decode_state(struct phylink_link_state *state,
793 unsigned int neg_mode, u16 bmsr, u16 lpa);
794void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs,
795 unsigned int neg_mode,
796 struct phylink_link_state *state);
797int phylink_mii_c22_pcs_encode_advertisement(phy_interface_t interface,
798 const unsigned long *advertising);
799int phylink_mii_c22_pcs_config(struct mdio_device *pcs,
800 phy_interface_t interface,
801 const unsigned long *advertising,
802 unsigned int neg_mode);
803void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs);
804
805void phylink_resolve_c73(struct phylink_link_state *state);
806
807void phylink_mii_c45_pcs_get_state(struct mdio_device *pcs,
808 struct phylink_link_state *state);
809
810void phylink_decode_usxgmii_word(struct phylink_link_state *state,
811 uint16_t lpa);
812#endif
813

source code of linux/include/linux/phylink.h

Morty Proxy This is a proxified and sanitized view of the page, visit original site.